Sell used Fluke 435 Power Quality Analyzer 3 Phase i430 FLEX Probe with All Installed Options.
| Condition | Used |
| Brand | Fluke |
| Model | 435 |
| Warranty | 3 month |
| Return available | 14 day |
Feautures:
| Energy loss calculator | Classic active and reactive power measurements, unbalance and harmonic power, are quantified to pinpoint true system energy losses in dollars (other local currencies available) |
| Power inverter efficiency | Simultaneously measure AC output power and DC input power for power electronics systems using optional DC clamp |
| PowerWave data capture | Captures fast RMS data, show half-cycle and waveforms to characterize electrical system dynamics (generator start-ups, UPS switching etc.) |
| Waveform capture | Captures 50/60 cycles (50/60Hz) of each event that is detected in all modes, without set-up |
| Automatic Transient Mode | Captures 200 kHz waveform data on all phases simultaneously up to 6 kV |
| Fully Class-A compliant | Conducts tests according to the stringent international IEC 61000-4-30 Class-A standard |
| Mains signaling | Measures interference from ripple control signals at specific frequencies |
| Troubleshoot | Analyze the trends using the cursors and zoom tools |
| Highest safety rating in the industry | 600 V CAT IV/1000 V CAT III rated for use at the service entrance |
| Measure all three phases and neutral | With included four flexible current probes with enhanced thin flex designed to fit into the tightest places |
| Automatic Trending | Every measurement is always automatically recorded, without any set-up |
| System-Monitor | Ten power quality parameters on one screen according to EN50160 power quality standard |
| Logger function | Configure for any test condition with memory for up to 600 parameters at user defined intervals |
| View graphs and generate reports | With included analysis software |
| Battery life | Up to 8 hours operating time per charge on Li-ion battery pack |
| Wireless data download |
|
Applications:
| Frontline troubleshooting | Quickly diagnose problems on-screen to get your operation back online |
| Long-term analysis | Uncover hard-to-find or intermittent issues |
| Load studies | Verify the available electrical system capacity before adding loads |
| PowerWave data capture | Capture every waveform for up to 5 minutes along with fast RMS values so you can determine how the voltage, current and frequency values are interacting |
| Power inverter efficiency | Measure the input and output power simultaneously to discover whether the inverter is optimized for its application |
| Energy monetization | Calculate the fiscal cost of energy waste due to poor power quality |
| Energy assessment | Quantify the before and after installation improvements in energy consumption to justify energy saving devices |
| Predictive maintenance | Periodic benchmarking of the power system can help detect and prevent power quality issues before they cause downtime |
Specifications:
|
Volt |
|
| Vrms (AC + DC) | Measurement range: 1 to 1000 V phase to neutral Resolution: 0.01 V Accuracy: ±0.1% of nominal voltage |
| Vpk | Measurement range: 1 to 1400 Vpk Resolution: 1 V Accuracy: 5% of nominal voltage |
| Voltage Crest Factor (CF) | Measurement range: 1.0 > 2.8 Resolution: 0.01 Accuracy: ±5% |
| Vrms 1/2 | Resolution: 0.1 V Accuracy: ±0.2% of nominal voltage |
| Vfund | Resolution: 0.1 V Accuracy: ±0.1% of nominal voltage |
|
Amps (accuracy excluding clamp accuracy) |
|
| Amps (AC + DC) |
|
| A Crest Factor (CF) | Measurement range: 1 to 10 Resolution: 0.01 Accuracy: ±5% |
| Amps 1/2 |
|
| Afund |
|
|
Hz |
|
| 50 Hz Nominal | Measurement range: 42.500 Hz to 57.500 Hz Resolution: 0.001 Hz Accuracy: ±0.01 Hz |
| 60 Hz Nominal | Measurement range: 51.00 Hz to 69.00 Hz Resolution: 0.001 Hz Accuracy: ±0.01 Hz |
|
Power |
|
| Watts (VA, var) |
|
| Power Factor (Cos j/DPF) | Measurement range: 0 to 1 Resolution: 0.001 Accuracy: ±0.1% @ nominal load conditions |
Fluke 435 Includes:
